Vibratory Ploughing

Ploughing Conditions:

Soil Type	Description	Ploughing
Sandy	Loose and granular soil, individual grains can be seen	Excellent
Clay	Fine textured soil which forms hard lumps or clods when dry	Excellent
Loam	Having a relatively even mix of sand, silt and clay	Good
Stony	Any of above types with a considerable amount of pebbles	Fair

Ploughing performance is effected by certain factors i.e.; A high clay content will allow easier ploughing because of the high moisture content, durability and ease of movement. Moisture loosens the soil and acts as a lubricant, allowing the shank to cut through a lot easier. Soil compaction relates to how much air and moisture is mixed into the soil. Highly compacted soil such as found under a graveled road will require more force to cut through.

Shank/Share Part	Description
Blade Body	The main backbone of the plough shank, usually made from high strength dropped steel with a high abrasion resistance
Shank/Share Rake Angle	The amount of angle the shank cutting edge lays back from vertical
Cutting Edge	The leading edge of the shank body which does the soil cutting. Usually wears to a dull point and with added hard surface welds, this will extend the shank life
Toe	Lowest and most forward part of the share body
Cable Chute / Laying Section	Attached to the trailing edge of the shank body into which cable or others is installed
Removable Cable Ribs / Gate	The Ribs are Installed into the back of the laying section which allows easy feeding of the cable through the laying section this alleviates the tension pulled through the cable chute
Radius	The Minimum bending radius of the cable to be installed
Cable Depth	The discharge location of the laying section is determined by toe depth, It is generally several centimeters above the toe depth.
Each of the above mentioned shank components has an effect on how well the shank will perform in given soil conditions. The following is a description of how each will affect productivity.

Shank/Share Part	Effect on Ploughing Performance
	The thicker the body material the more force is required to pull it through the soil. Thin shank blades pull easier. Depending on the width of the laying section, different size cutting blades can be fixed on to the front edge of the shank
Shank/Share Rake Angle	The closer to vertical the cutting edge, the more tendency a share will have to coming out of the ground as it is being pulled. The more laid back the angle the more a share will pull down into the ground
Cutting Edge	As the cutting edge becomes blunt, the more force and horse power is required to pull the plough/shank through the ground. Hard surfacing welds to the cutting edge will extend the life of the cutting edge and shank
Toe	The size, width and mounting angle of the toe all effect whether a shank cuts easier and dictates the cable chute size.
Cable Chute / Laying Section	Wider laying sections to accommodate larger diameter cable pull harder than narrow sections for smaller cable
Radius	Larger diameter cable generally requires minimum bending radius. The larger the bending radius, the longer the cable curve radius required. Larger cable chute/laying section length causes more side surface area to drag through the soil requiring more draw pull force. Smaller cable chutes and bend radius generally pull easier through the ground.
Cable Depth	The deeper the ploughing depth the larger the draw bar required. Generally, installing cable 170cm depth requires more than twice the draw bar pull than to install cable at 75cm deep
The unique cable chute / sanding hopper and plough shank design is only available to our plough design. The sanding chute and cable laying section allows the shank assembly to hinge on the front of the cable chute, this allows the cable to be drawn around shallow bends and corners. The sand or finefill hopper provides added protection for delicate cable such as Fibre Optic, Plastic Pipes, Pipes for Water / Gas Industries and low voltage / high voltage electric power cable

Vibrator:

The last major component which affects plough productivity is the speed and amount of vibration that is applied to the shank / share blade. The vibrator consists of counter-rotating eccentric weights. The faster the weights rotate, the more force they produce. The benefit of vibratory ploughing over static ploughing is that with the help of the vibratory force, the toe and cutting edge of the shank / share lift fracture the soil before the shank body and laying section are pulled through by the crawler. When ground conditions are dry or high compaction exists, high speed and force is required to break up the soil. As the operator can adjust the vibrator from inside the comfort of the cab, he can concentrate on the ploughing force rather than the plough speed. The harder the ground the slower the ploughing speed will be. If the ground conditions are soft the operator can accelerate the speed to optimise the performance given by the plough.

Turf Cutter:

When ploughing conditions are established in grassland or crop conditions where shallow roots exist, the addition of a turf cutter attachment is advised to once again minimise ground disturbance and restoration. The design of the cutting edge of the turf cutting blade will cut separated grass and roots in a down cutting motion which then allows the plough shank blade to pass without snagging the roots and pulling them up to the surface.

Plough Offset:

Many job sites require installing a utility close to an obstruction (building, fence line etc). To accomplish this, the plough can swing to the side of the machine and steer the plough shank blade in the direction of travel. This offsets the machine from the plough shank and allows the machine to pass by the obstruction. This feature also makes ploughing around corners much easier.

More Plough Features:

a) Drum mounting b) Drum brake c) Guide roller d) Lifting mechanism e) Vibrator f) Roller quadrant g) Plough share h) Cable-laying section i) Cable or duct j) Screening conductor k) hazard-warning

This fitment will undertake our 132KV cable installations, the cable drums can weigh up to 11 tonne each hence the separate drum trailer formation. The tractor plough will be A D10 or Leibherr 764 size.